Dark Detector Light Circuit using LDR – Easy Tutorial



Dark Detector Light Circuit using LDR – Easy Tutorial

Welcomes you in Easy Way

Hey there,
Here’s a super simple tutorial on making a dark sensor circuit or automatic light. Such a circuit is used in street lights and other motion related circuits. The schematic of this circuit is well available on the internet. In case you get stuck up, just leave a comment ! If you enjoyed this, do subscribe and stay tuned for more.

https://www.youtube.com/channel/UCbH08-EqQ4X2UJxvXrP4_fg

What is a Light Dependent Resistor or a Photo Resistor?

A Light Dependent Resistor (LDR) or a photo resistor is a device whose resistivity is a function of the incident electromagnetic radiation. Hence, they are light sensitive devices. They are also called as photo conductors, photo conductive cells or simply photocells. They are made up of semiconductor materials having high resistance. There are many different symbols used to indicate a LDR, one of the most commonly used symbol is shown in the figure below. The arrow indicates light falling on it.

Working Principle of LDR

A light dependent resistor works on the principle of photo conductivity.Photo conductivity is an optical phenomenon in which the materials conductivity is increased when light is absorbed by the material. When light falls i.e. when the photons fall on the device, the electrons in the valence band of the semiconductor material are excited to the conduction band. These photons in the incident light should have energy greater than the band gap of the semiconductor material to make the electrons jump from the valence band to the conduction band. Hence when light having enough energy strikes on the device, more and more electrons are excited to the conduction band which results in large number of charge carriers. The result of this process is more and more current starts flowing through the device when the circuit is closed and hence it is said that the resistance of the device has been decreased. This is the most common working principle of LDR.

Photocells or LDR’s are nonlinear devices. There sensitivity varies with the wavelength of light incident on them. Some photocells might not at all response to a certain range of wavelengths. Based on the material used different cells have different spectral response curves.When light is incident on a photocell it usually takes about 8 to 12 MS for the change in resistance to take place, while it takes one or more seconds for the resistance to rise back again to its initial value after removal of light. This phenomenon is called as resistance recovery rate. This property is used in audio compressors. Also, LDR’s are less sensitive than photo diodes and photo transistor. (A photo diode and a photocell (LDR) are not the same, a photo-diode is a p-n junction semiconductor device that converts light to electricity, whereas a photocell is a passive device, there is no p-n junction in this nor it “converts” light to electricity).
Types of Light Dependent Resistors
Based on the materials used they are classified as:
1. Intrinsic photo resistors (UN doped semiconductor): These are made of pure semiconductor materials such as silicon or germanium. Electrons get excited from valance band to conduction band when photons of enough energy fall on it and number charge carriers is increased.
2. Extrinsic photo resistors: These are semiconductor materials doped with impurities which are called as dopants. Theses dopants create new energy bands above the valence band which are filled with electrons. Hence this reduces the band gap and less energy is required in exciting them. Extrinsic photo resistors are generally used for long wavelengths.

Applications of LDR
LDR’s have low cost and simple structure. They are often used as light sensors. They are used when there is a need to detect absences or presences of light like in a camera light meter. Used in street lamps, alarm clock, burglar alarm circuits, light intensity meters, for counting the packages moving on a conveyor belt, etc.

Component Used-
1. BC547
2. LDR Sensor
3. 1k ohm Resistor x2
4. LEDs (Any Colour)
5. Preset (50k)
6. 9v battery
7. 9v Battery Connector
8. Breadboard
9. Single Core jumper Wire.

Thanks for watching my Video.

Background Music:- https://www.youtube.com/watch?v=bM7SZ5SBzyY

Like my Facebook page-

https://www.facebook.com/easywayjasveersingh/app/212104595551052/


Post time: 10-12-2017